A photographer friend of mine asked me to make one of these for her photo studio. It is a bit different from what I normally like to do, and as much as I dislike panted finishes I an mot a man to turn away a challenge. I learned a few things along the way and hope to share those with you here.
Long nosed marker: http://amzn.to/2lExV1e
Coping saw: http://amzn.to/2kCe68X You could also use a turning saw or jig saw
Panel saw: http://amzn.to/2hjAura
Bit set: http://amzn.to/2hZVT5T
#4 Hand plane: http://amzn.to/2hc6LQZ
Block Plane: http://amzn.to/2ikkaqg
Flat spokeshave: http://amzn.to/2lKn6ND
File set: http://amzn.to/2l0czdB
Paint brush: http://amzn.to/2nnsGpA
Pull saw: http://amzn.to/2n4EMRL
Compass Pencil: http://amzn.to/2n4FgYq
1 X 12 X 4′ Pine (1): http://amzn.to/2n2xGg1
1 X 2 X 4′ Pine(2): http://amzn.to/2nzgiDo
2 X 2 X 8′ Pine stud grade (2)
Flexible plywood: http://amzn.to/2nhTFkQ
wood glue: http://amzn.to/2kEeTHc
Wood Filler: http://amzn.to/2ohjyAi
Shape the Bananas
I start by making a template out of scrap cardboard. there is no hard and fast design to this I just drew something I likes with the seat 12″ off the ground. that seamed good for the kids. the circle has about a 24″ diameter on the outside and the ring is 1.5″ thick.
I use a marker to trace out the template onto the piece of clear 1X12 pine.
Next use a coping saw or jig saw to cut out the shape. You will need 2 of these curves (bananas).
I wanted the legs to be 1.5″ squared so rather then cutting them out of 2X2s I decided to laminate them so there would be a half lap joint at the top where it meets the bananas.
I cut 4 pieces at 11″ and 4 at 12.5″ then glued them up in pairs.
Glue up Assembly
it is important that the front and back match so when I glue the legs tot he bananas I want them to be perfectly lined up.
To do this I clamp the two bananas together. then I clamp two pairs of legs together so the half lap joints face each other.
With these in place I can add glue and slide the leg pairs on to the bananas and add clamps.
This way when I take the clamps off I am left with a matching front and back shape of the seat.
Next we need to separate the front and back. this will be done with 2X2s they are the same thickness as the bananas. I place them every 4-6″ spanning between the two frames.
Start by cutting all of the spacers at 10.5″. Then pre-drill and countersink all the screw holes in the bananas. we do not want them splitting.
Then with 2 1/2″ screws and glue attach the spacers so they are flush with the bottom and top of the seat.
For the last two on eather side of the seat I used 2X4s but you could also use 2X2s there too. just make sure it is flush with the bottom and top and sticks out on the end of the banana seat.
Trim off End Supports
You will want to trim the last space back to be flush with the bottom top and outside edge of the banana.
I did this with a panel saw and hand plane. it made quick work of smoothing it out.
I decided to use this roll wood used for facing columns in the basement. I got it at the local home center, but if I had to do it again I would use 2 layers of 1/8″ ply wood like I have listed int he supplies.
With a flexible tape measure, measure the width and length of the seat. then cut it to dimension. I decided to make mine about 1/2″ larger in both directions so I could cut off the excess.
To attach it down I just used wood glue and clamps to hold it in place. you could also use brad nails.
After letting the glue dry overnight I trimmed off the excess with a pull saw or flush cut saw.
Trim Off and Fill Edges
Now it is time to smooth out all the edges. I used a spoke shave to round over all the edges. and give it a smooth look.
Then I used Wood Filler to fill all the cracks, voids, and screw heads. and after it dried I sanded off the wood filler with a file.
Paint and Refill
This is the step that does not end. I applied a thin first coat of primer, but this shows off all the imperfections.
Once that coat dries, you can add more wood filler.
then let that dry and sand it again and paint again. I did this 3 times tell I was satisfied the look.
I had left the legs long tell now to let any wood movement have its way.
I set the bench flat on a table and put a spacer under the one leg that wobbled tell the bench was flat.
With a Pencil Compass, I marked all around each leg with a line that is parallel to the surface.
With a hand saw I can then cut the legs off at that line. last, I want to add a chamber to all the bottoms so that they will not chip out when moved across the floor.
At this pint it just needs a final paint. take your time and make it look nice.
It is not a difficult project if broken down int the steps and taken one section at a time.